Today I finished the floor. The rear floor had been installed but needed to be bolted down. I ran out of the closet bolts that I bought, so I found some different ones that I had at my plant. They are black and have an allen key, but were similar in size. The Airsteam bolts were self tapping and my new bolts were not, so I had to drill the floor and then tap each hole before with a 1/4-20 tap, so I could secure the bolts to the floor. It did not take as much time as I expected. I also added some thread lock to the bolts before I screwed them down. I had a small section of floor in the front of the trailer (24"x 35"), that still needed to be filled. I was able to do this in a short amount of time. It was cut to size and bolted to the new frame members and to the C-channel in the wall. It is nice to be able to walk in the trailer and not fall through to the ground. With all of the floor in, I was able to start to re-attach the interior walls. I had a purchased a hydraulic rivet gun from Harbor Freight. The dam thing will do a bout 100 rivets and then I need to re-fill it with more hydraulic fluid. Needless to say, every time I pull the trigger it sprays a nice mist of fluid all over the place. I have taken the dam thing apart, but can not figure out what seal is bad. I'm close to being done, so I may just deal with it. I had to finish the day a little early because I had to get to a Xavier basketball game.
Sunday, February 15, 2009
Finish the Floor
Today I finished the floor. The rear floor had been installed but needed to be bolted down. I ran out of the closet bolts that I bought, so I found some different ones that I had at my plant. They are black and have an allen key, but were similar in size. The Airsteam bolts were self tapping and my new bolts were not, so I had to drill the floor and then tap each hole before with a 1/4-20 tap, so I could secure the bolts to the floor. It did not take as much time as I expected. I also added some thread lock to the bolts before I screwed them down. I had a small section of floor in the front of the trailer (24"x 35"), that still needed to be filled. I was able to do this in a short amount of time. It was cut to size and bolted to the new frame members and to the C-channel in the wall. It is nice to be able to walk in the trailer and not fall through to the ground. With all of the floor in, I was able to start to re-attach the interior walls. I had a purchased a hydraulic rivet gun from Harbor Freight. The dam thing will do a bout 100 rivets and then I need to re-fill it with more hydraulic fluid. Needless to say, every time I pull the trigger it sprays a nice mist of fluid all over the place. I have taken the dam thing apart, but can not figure out what seal is bad. I'm close to being done, so I may just deal with it. I had to finish the day a little early because I had to get to a Xavier basketball game.
Saturday, January 24, 2009
Steppin' it up
Thursday, January 22, 2009
Floorin it
Last night I started putting the floor back in the Airstream. All my welding, painting and frame work are now done. It's time to start putting the darn thing back together. I decided to start with the floor near the front door because I thought it would be easier to fit. Not exactly easy but by the end of the night, it was in place. I took some measurements from the side wall to the main beam in locations where I knew it had not moved. I then cut a piece of 1/2" plywood to 35-3/4 x 8'. I used this measurement because it would hit on the center of a support and I could bolt it to the frame. The wall close to the door was not supported and could be moved at least an inch inward and an 1" away from the trailer. Since my plywood was cut at a constant distance and my cut in the original floor was cut perpendicular to the trailer frame, I should be straight when it all gets bolted back together. One thing I remembered the next morning was that I did not install the aluminum shield that goes above the steps and under the floor. The aluminum protects the underside of the plywood floor because in the step location it is not insulated or sealed from the weather. I am hoping that I can just lift the plywood up and wedge it above the step stringers and I do not have to completely remove the floor.
Saturday, January 10, 2009
Paint it Black
Tuesday, January 6, 2009
Its welding time
Wednesday, November 12, 2008
Just a little rust
I dropped the black
and grey tanks so I could get a good look at my frame situation. It was not good! Just a little rust! The rear cross member was completely rusted out. The center support that ran between the grey and black tanks was almost gone. I took some measurements and drew up what I needed with AutoCad and had a local shop make me some replacements. As it turned out they made my new brackets out of galvanized sheet and
I am hoping that I will never have to replace them again.
Friday, September 12, 2008
I'm infamous
I'm now In-Famous, that's more than Famous (quote from the Three Amigos). I made the VAP! Vintage Airstream Podcast. This is a Podcast that comes out every 2 weeks. It consists of a host Tim Sheppard and 2 panel professionals Rob Baker and Colin Hyde. The podcast covers all things Airstream. From total restorations to traveling across the country to Airstream ralleys. They had been looking for people to call-in and talk about their year of Airstreams for a couple of episodes, but no one was calling. They wanted people from each year to call in on the episode that matched their year. I called in on the 78th episode because I had a 78' Airstream Soviergn. If you have 56 minutes to kill, 26megs of hard-drive space, and want to hear everything about Airstreams go and download it. 78th episode Rob Baker pretends to dislike everything about the 70's Airstreams, so that's why I'm hassling him on the podcast. You think I'm nuts about my airstream... Rob and Colin at any one time may own upwards of 5 to 10 each!
Subscribe to:
Posts (Atom)